Shenzhen Mingjiada Electronics Co., Ltd. supplies the Infineon IPW65R115CFD7A 650V CoolMOS™ CFD7A N-channel automotive-grade power MOSFET.
I. IPW65R115CFD7A Device Positioning and Core Overview
The IPW65R115CFD7A is a 650V N-channel enhancement-mode power MOSFET developed by Infineon based on the CoolMOS™ CFD7A technology platform, and forms part of Infineon’s high-voltage superjunction power device product line. Designed for power electronics applications requiring high power density, high efficiency and high reliability, this device utilises a Superjunction structure to resolve the inherent trade-off between high voltage rating and low on-resistance, whilst being specifically optimised for the demanding operating conditions encountered in automotive electronics and industrial applications. The device utilises a standard TO-247-3 through-hole package, facilitating soldering and thermal management on power circuit boards. It is suitable for circuit topologies requiring high-voltage power switches, such as switching power supplies, on-board charging, industrial inverters and power conversion.
II. Analysis of Key Electrical Parameters of the IPW65R115CFD7A
1. Voltage Rating and Current Rating
The IPW65R115CFD7A has a drain-source rated voltage (VDS) of 650 V, which covers the power conversion requirements of 400 V DC bus systems. It offers sufficient voltage headroom to cope with voltage spikes and switching transient overvoltages in the circuit. At a case temperature of 25°C, the device’s continuous drain current (ID) can reach tens of amperes; the specific current-carrying capacity varies dynamically with the package’s thermal conditions and operating temperature, meeting the current transmission requirements of medium-to-high-power circuits. The device’s avalanche rating has been specifically designed to withstand single-pulse avalanche energy for a limited duration, enhancing the circuit’s robustness under abnormal operating conditions.
2. On-resistance RDS (on)
The ‘115’ in the model suffix of the IPW65R115CFD7A corresponds to the device’s typical on-resistance, i.e. RDS (on) is approximately 115 mΩ. When driven by the rated gate-source voltage, the impedance of the device’s on-channel falls within the optimised range for super-junction MOSFETs in the same voltage rating class: the low on-resistance reduces the device’s on-state voltage drop, minimising on-state losses and heat generation, whilst preventing excessive chip temperature rise under high-current conditions. Under high-temperature operating conditions, the on-resistance increases moderately as the junction temperature rises; during design, derating calculations for on-resistance losses must be performed in conjunction with the maximum operating junction temperature to ensure long-term thermal stability.
3. Gate Parameters and Drive Characteristics
The IPW65R115CFD7A device features standardised gate-source threshold voltage (VGS(th)) and gate charge (Qg) specifications; its gate drive circuit is compatible with the output capabilities of mainstream MOSFET driver ICs. The CoolMOS CFD7A platform features optimised gate structure and capacitance parameters; the device’s input capacitance (Ciss), output capacitance (Coss) and reverse transfer capacitance (Crss) have been balanced in design to ensure stable gate control whilst minimising drive losses and the effects of the Miller effect during switching. The device supports a standard gate drive voltage of approximately 10 V, whilst also being compatible with certain low-voltage drive solutions; however, care must be taken during design to ensure the gate voltage remains within the rated range to avoid damage due to overvoltage or insufficient conduction.
4. Switching Performance and Dynamic Parameters
As a super-junction power MOSFET, the IPW65R115CFD7A offers fast switching speeds, which help to reduce switching losses in high-frequency switching topologies. The device’s turn-on and turn-off delays, as well as rise and fall times, have been optimised through platform-based engineering to support reliable operation in hard-switching circuits; regarding reverse recovery characteristics, the CFD7A series has optimised the reverse recovery performance of the body diode, reducing losses and voltage oscillations during the body diode recovery process, thereby delivering more stable performance in topologies such as bridge circuits and inverter circuits where body diode turn-on current is present.
![]()
III. Features of the CoolMOS CFD7A Technology Platform
1. Principles of the Super-Junction Structure
The CFD7A belongs to the seventh-generation CoolMOS super-junction technology branch from Infineon. By forming an alternating arrangement of P-type and N-type doped pillars within the silicon wafer, it overcomes the trade-off between breakdown voltage and on-resistance inherent in traditional vertical power MOSFETs. At the same 650 V voltage rating, the super-junction structure allows for a thinner drift region and higher doping concentration, thereby significantly reducing on-resistance and on-chip conduction losses; at the same time, it retains the voltage withstand capability required for high-voltage devices, achieving an optimised balance between breakdown voltage, on-resistance and chip area.
2. Automotive-Grade Reliability Design
The IPW65R115CFD7A has obtained automotive electronics certification and meets the requirements for temperature cycling, humidity and heat, vibration, and long-term reliability specified for automotive-grade semiconductors. The CFD7A platform enhances device robustness at both the process and packaging levels: the gate oxide structure offers a higher reliability margin, whilst the solder joints between the chip and leads are subject to automotive-grade process control, ensuring parameter stability across a wide temperature range and under long-term service conditions. Compared to industrial-grade MOSFETs of the same class, the automotive-grade version adheres to stricter standards regarding batch consistency, long-term failure control and reliability verification, making it suitable for in-vehicle electronic systems with stringent requirements regarding failure rates.
3. Robustness and Immunity to Interference
The CFD7A series has been specifically optimised to address oscillations, parasitic parameters and abnormal operating conditions encountered in real-world power circuits. The device’s internal structure exhibits excellent tolerance to dv/dt variations, thereby mitigating the risk of false conduction during the switching process; the parasitic parameters of the body diode and switching nodes have been calibrated to reduce the likelihood of voltage spikes and electromagnetic interference within the circuit. Under fault conditions, the device possesses a certain degree of avalanche and overload resistance; when combined with external protection circuits, this enhances the operational safety of the entire power system.
IV. IPW65R115CFD7A Packaging and Thermal Design Considerations
The IPW65R115CFD7A utilises a TO-247-3 package, with three pins corresponding to the drain, source and gate respectively; the drain is connected to the metal heat sink on the rear of the package. This package offers a large heat dissipation area and high current-carrying capacity, enabling heat from the chip’s junction to be conducted to an external heat sink via the installation of a heat sink.
In terms of thermal design, particular attention must be paid to parameters such as the junction-to-case thermal resistance (Rth(jc)) and the case-to-heat sink thermal resistance. The maximum junction temperature must be calculated based on actual power dissipation to ensure that the junction temperature does not exceed the rated upper limit under full-load conditions. As the on-resistance of a MOSFET increases with rising temperature, sufficient thermal margin must be provided under high-current conditions to prevent the chip from entering a thermal runaway state. During soldering and installation, good contact must be ensured between the bottom of the package and the heat sink; thermal grease should be applied or thermal pads used to reduce interfacial thermal resistance; pin traces should be designed for wide current-carrying capacity to minimise circuit resistance and additional heat generation.
V. Typical Application Scenarios for the IPW65R115CFD7A
1. On-board Charging and On-board Power Supplies
Designed for on-board power electronic units in new energy vehicles, such as on-board chargers (OBCs) and DC-DC converters, the IPW65R115CFD7A can function as a high-voltage-side power switch in power conversion. Its automotive-grade reliability and 650V voltage rating are well-suited to high-voltage busbar systems in vehicles, whilst its low on-state losses and stable switching characteristics help to improve charging and conversion efficiency, whilst reducing heat generation and the physical size of on-board power modules.
2. Industrial Switch-Mode Power Supplies and Power Conversion
Suitable for main switching circuits in industrial-grade switch-mode power supplies, server power supplies and AC-DC conversion modules, it acts as a high-voltage switch in PFC (Power Factor Correction) and full-bridge/half-bridge conversion topologies. The low-loss characteristics of super-junction devices help improve the overall efficiency of the power supply, meeting the requirements of industrial equipment for high efficiency and high power density.
3. Inverters and Motor Drive Circuits
In topologies such as industrial inverters, uninterruptible power supplies (UPS) and high-power motor drives, this MOSFET can function as a switching device in bridge circuits to facilitate power conversion. The optimised free-wheeling characteristics of the body diode and its resistance to oscillation ensure stable operation of the bridge circuit under free-wheeling conditions, whilst reducing reverse recovery losses.
4. Renewable Energy and Energy Storage Systems
It can be applied in new energy power electronic equipment such as photovoltaic inverters and energy storage converters, performing switching and conversion functions on the high-voltage DC side. The device’s wide operating temperature range and high-reliability design meet the requirements for long-term continuous operation in outdoor and industrial environments.
VI. Design Considerations for the IPW65R115CFD7A
Firstly, gate drive circuit design. The peak current capacity of the driver IC must be matched to the device’s gate charge and capacitance parameters; the gate series resistance should be set appropriately to balance switching speed, losses and the risk of oscillation. A pull-down resistor may be connected in parallel between the gate and source to ensure a reliable gate level when power is off and to prevent unintended conduction due to a floating gate. The drive voltage must be kept within the rated gate-source voltage range and must not exceed the maximum gate-source withstand voltage.
Secondly, buffering and suppression circuits. Depending on the circuit layout, RC buffers or clamping devices may be configured near the switching nodes to absorb transient voltage spikes during switching, thereby reducing the overvoltage and electromagnetic interference to which the device is subjected; in terms of layout, the area of power loop traces should be minimised to reduce parasitic inductance and minimise voltage oscillations during the switching process.
Thirdly, thermal management and derating design. During actual circuit design, a comprehensive calculation of conduction losses and switching losses must be carried out, and the maximum junction temperature must be verified in conjunction with the heat sink’s thermal resistance; derating for voltage, current and temperature must be applied in accordance with the operating conditions to prevent the device from operating at the limits of its rated specifications for extended periods, thereby ensuring long-term reliability.
Fourthly, layout and control of parasitic parameters. The power and drive circuits should be laid out separately; gate traces should be kept as short and straight as possible to minimise parasitic inductance in the drive circuit; drain power traces should be widened and thickened to reduce line impedance and heat generation; when installing the device, ensure reliable pin soldering to avoid cold solder joints and stress-induced damage.
VII. Summary of the IPW65R115CFD7A
The IPW65R115CFD7A is a 650 V automotive-grade N-channel power MOSFET within Infineon’s CoolMOS CFD7A platform. It utilises super-junction technology to achieve a balance between low on-resistance and high voltage rating, whilst its TO-247-3 package provides excellent thermal dissipation and power handling capabilities. Automotive-grade reliability verification, along with optimised body diode and switching dynamic characteristics, make it suitable for a wide range of high-voltage power applications, including on-board chargers, industrial power supplies, inverter drives and new energy conversion systems. During actual component selection and circuit design, parameter calculations and derating must be carried out in conjunction with the specific topology, thermal conditions and drive scheme to fully leverage the device’s technical advantages in terms of efficiency, stability and reliability.
Personne à contacter: Mr. Sales Manager
Téléphone: 86-13410018555
Télécopieur: 86-0755-83957753